Category Archives: quads

Mini H Quad – New FC

So my H Quad just got a new flight controller, a CC3D board from banggood

2014-10-15 23.02.41

I de-soldered the headers on the rx and the CC3D board and changed them for the right angles ones you can see.

De-soldering these was a complete pain but the method I came upon was this:

You’ll need a decent pair of mini side cutters such as these

You’ll also need to fix the pcb down so it doesn’t move about.

Step 1: Cut the pins in half to reduce the thermal mass.

Step 2: Try and work your cutters between the black plastic portion to separate the pins in to individual parts, this will make it easier later.

Step 3: Cut the solder pads as close to the pcb as you can.

Step 4: Apply some flux to the bottom connections and use solder wick to remove as much solder as possible.

Step 5: Now take a sewing pin or a single header pin held between the jaws of some pliers and using your soldering iron heat the pin in the pliers and the pad in order to push the pin you’re trying to remove out.

Next time I do this procedure I’ll try and take some pictures to illustrate better.

Then is was a case of running the openpilot s/w and configuring the airframe and a quick flight to verify it.

 

Mini H Quad – Build log 4

Bottom plate is now fully wired.

Each arm is connected with 2 short screw and 2 long ones, the short ones go through one 5mm spacer and the long ones point upwards with a 5mm on the bottom and another on the top with an m3 nut to hold them in place.

This means that the bottom plate is a sub assembly and can be taken off the quad to be worked on if needs be.

At the front is a small 6 way black connector and there is a small plug in wire harness to connect to the flight controller on the 2nd plate.

2014-08-07 18.52.42

Just waiting for some more 5mm spacers to finish of the last arm and then the bottom can be mated to the top and the flight controller wired before first testing.

 

 

Mini H Quad – Build log 3

A few bits and pieces done today on the quad but I’m running out of bits I can do until my micro power distribution board and other bits and pieces including some liquid electrical tape.

I’ve removed the motor connection wires from 2 of the ESC’s and shortened the motor wires and soldered these direct to the ESC pads, I then tested which way this combination of wires made the motors turn by connecting the signal lead up to channel 3, throttle, on my 6 channel flysky receiver.

2014-08-03 18.44.27

Both ESC’s have been wired up the same so that’s the 2 anti colockwise ones done and after I tested them I then removed the gnd and positive leads from the servo connector and de-soldered them from the PCB to save a bit of weight and make the wiring tidier.

Mini H Quad – Build log 2

Ok a bit more progress made on the mini H.

I returned home from holiday to a small box containing motors, esc’s and props.

I’ve rebuilt the frame using some nylon spacers so that there is room between the bottom 2 plates for a micro power distribution board.

The esc will be attached to the arms with heat shrink and the motor leads will be soldered directly to the esc pads to reduce the amount of wire.

At the moment I’m using my witespy quads Multi Pro 2 flight controller and it’s been secured in place with some foam pads but in the future I intend to use one of their Flip32+ FC’s

The good thing about this FC is that it has plenty of connections available and as you can see in the pic I have my Bluetooth module installed so that I can configure MultiWii from my android phone, I’ve temporarily powered the FC using one of my esc hooked up to a flight battery and it all connected ok.

2014-08-02 21.30.13

Mini H Quad – build log 1

A few months ago I got started in the hobby of RC multi rotors and specifically quad copters.

My first quad was based on a 3d printed design downloaded from thingiverse and modified through several iterations.

This quad is big and heavy and gives me about 5 minutes flight time from a 2200mah lipo pack so I decided to go for something smaller and more manoeuvrable with the ability to easily add FPV gear to it.

To meet these goals I’ve decided to build a small 250 H quad based on a carbon fibre frame from Banggood so let’s get to it.

Parts List:

Frame – Banggood ZMR250 carbon fibre alternative Banggood ZMR250 glass fibre

Motors, Esc’s & Props – This combo package from myrcmart.com but any similar sized motor, esc etc… can be used

RC Receiver – Any suitable 6 channel receiver that matches your TX

Battery – 1400mah + I’m using these from hobbyking

Flight Controller – At the moment I’m going to use the FC from my other quad which is a Multiwii Pro 2.0 from witespyquads but I intend to eventually put one of their Flip 32+ FC’s on this quad which is equivalent to a Full Naze 32

That’s all for now hopefully the frame will be delivered this week and I can get that build and take some pictures whilst waiting for the other parts to be delivered.

Mini H Quad frame Frame arrived today.